Comparison
Anker SOLIX C1000 vs C1000 Gen 2: Which Generation Should You Buy?
Choose the right Anker SOLIX C1000 generation: compare BP1000 battery compatibility, charging conditions, US variants, bundles and equal-load runtime estimates.
By thisWATT EditorialUpdated November 2, 20268 min read
Choose the Anker SOLIX C1000 Gen 2 for a lighter standalone station and faster wall recharging; choose the original C1000 if you need an expansion battery. The original C1000 supports BP1000 expansion, bringing storage to 2,112Wh; Gen 2 cannot expand (Anker's expansion FAQ). Anker's current BP1000X page specifies SOLIX C1000; confirm the exact station and battery labels with Anker before ordering.
Quick picks
| Your priority | Pick | Deciding trade-off |
|---|---|---|
| Frequent refills and easier carrying | C1000 Gen 2 | Faster published wall recharge; no battery expansion |
| More stored energy for outages | Original C1000 / C1000X | Supports a matching expansion battery; heavier station |
| Extend an original you already own | BP1000 / BP1000X family | Extra storage, used through the station; cannot operate alone |
For alternatives across brands, use our 1 kWh power-station comparison. This page resolves the C1000 generation and bundle choices.
The US generations compared
These are Anker's published figures, with the original US overview and product specifications compared against the Gen 2 specifications.
| Specification | Original C1000 family, US | C1000 Gen 2, US |
|---|---|---|
| Battery capacity | 1,056Wh | 1,024Wh |
| Continuous AC output | 1,800W | 2,000W |
| AC outlets | 6 | 5 |
| USB-C outputs | 100W + 30W | 140W × 2, plus 15W |
| Maximum wall charging, UltraFast | 1,300W | 1,600W |
| Maximum solar input | 600W | 600W |
| Expansion | To 2,112Wh with matching battery | None |
| Weight, station only | 28.44 lb | 24.9 lb |
| Published cycle rating | 3,000 cycles to 80%+ capacity | 4,000 cycles to at least 80% |
| UPS switchover | 20 ms in US overview | 10 ms in spec table |
The original's product table says under 20 ms, whereas its US overview says 20 ms; Gen 2's feature copy says under 10 ms, whereas its spec table says 10 ms. These are maker figures, not a guarantee for every connected device.
Read peak figures cautiously. The original's product table labels 2,400W as “AC Surge Output,” while its overview describes 2,400W as SurgePad. The Gen 2 comparison table instead prints a 3,000W peak for the original. These are conflicting descriptions: use the original's consistent 1,800W continuous rating for sizing, and confirm an appliance's starting requirement with Anker. SurgePad's FAQ specifically excludes precision devices with strict voltage requirements.
Best standalone station: C1000 Gen 2
Gen 2 suits buyers who refill regularly and carry the station between uses. Its 2,000W continuous output, 24.9 lb weight and published 49-minute refill make it our standalone choice; Anker also publishes a 3,000W peak, separately from continuous output.
There is a useful USB change: Anker's detailed product data lists two 140W USB-C outputs plus a 15W USB-C output. The visible specification section shows only one high-power USB-C entry, so the fuller port breakdown comes from the page's detailed data. The 15W USB-C port shares a 20W total with USB-A. Match your laptop's charging requirement to the relevant port.
Best for expansion: original C1000 / C1000X
Choose the original when extra stored energy matters more than carrying weight. It holds 1,056Wh, supplies 1,800W continuously, and supports a matching battery for 2,112Wh total. Anker's original-plus-battery listing still describes 1,800W output: adding storage does not upgrade the inverter.
Naming needs care. Anker's current US /products/c1000 page titles the product C1000X, while its specification heading says C1000. Anker publishes a shared C1000/C1000X manual. Treat those as original-family names here, and confirm the delivered model and region with the seller.
Check the original generation at Anker.
Best add-on for an original: BP1000 / BP1000X
Anker's current US battery option is titled BP1000X and says it works with SOLIX C1000. Its shared BP1000/BP1000X manual gives 1,056Wh and 19.97 lb; the store identifies an LFP battery. Confirm the exact station and battery labels with Anker before ordering.
The battery cannot be used alone: charging and discharging go through the power station. The manual says the station charges first, followed by the expansion battery. Consequently, the station-only rapid-charge time is not a published refill time for the expanded pair. Check that the battery connection cable is included, especially with a separately offered battery.
Check the current BP1000X option at Anker.
Tap a label to explore. You can also hover or use your keyboard.
Scroll across to see every column
| Option | BP1000 / BP1000X |
|---|---|
Original C1000Anker's original manual names BP1000 expansion; the current BP1000X page specifies C1000. Confirm exact station and battery labels with Anker. Sources: 1: The original C1000/C1000X manual specifies BP1000 expansion., 2: The current BP1000X store page specifies C1000 compatibility. | Yes |
C1000 Gen 2Anker says Gen 2 does not include an expansion feature. Sources: 3: C1000 Gen 2 has no expansion feature. | No |
Source notes3 references
The original C1000/C1000X manual specifies BP1000 expansion.
salesforce-knowledge-download.s3.us-west-2.amazonaws.com — source for The original C1000/C1000X manual specifies BP1000 expansion.Your power station can be connected with an expansion battery to double the capacity to 2112Wh. Please refer to the user manual of Anker SOLIX BP1000 Expansion Battery (1056Wh) for detailed instructions.
The current BP1000X store page specifies C1000 compatibility.
www.ankersolix.com — source for The current BP1000X store page specifies C1000 compatibility.Works seamlessly with SOLIX C1000
C1000 Gen 2 has no expansion feature.
www.ankersolix.com — source for C1000 Gen 2 has no expansion feature.To improve portability by reducing weight and size, it does not include an expansion feature.
Read the model and region before the bundle name
Anker's current US product data gives A1761111 for the original-family store option and A17631A1 for Gen 2. Compare the seller's model-label photograph with the selected item, capacity and outlet region. Use Anker's original-family photographs and Gen 2 photographs as visual references; they do not replace the electrical label.
The US overview specifies 120V AC input for the original; Gen 2's US table specifies 120V output. The shared original manual linked above is a UK edition with 220–240V input. We use it for expansion and maintenance instructions, with US electrical figures taken from the US pages. Do the same when comparing imported listings.
Recharge modes and solar conditions
Wall charging: Anker quotes 58 minutes to full for the original with UltraFast enabled in the app. Gen 2's 49 minutes likewise requires app-enabled UltraFast at 1,600W, versus 1,200W normal. These are manufacturer claims for the station, rather than times we independently verified.
Cold cells: Gen 2's FAQ says UltraFast activates above 68°F battery-cell temperature; charging from 32°F to 68°F is significantly slower. Anker recommends using UltraFast only when necessary to prolong battery lifespan. A station brought out of cold storage can miss the headline time.
Solar: Both advertise 600W maximum and a 1.8-hour full solar recharge. The original's FAQ specifies 11–32V at 10A maximum, then 32–60V at 12.5A maximum, using XT-60. Gen 2's published MPPT bands are 11–28V at 8.2A and 29–60V at 14.5A, with an XT60i input. Check the exact panel voltage, current and cable; a panel's wattage label alone does not establish compatibility or charging speed.
Combined inputs: The original prioritizes AC and cannot charge from AC and DC simultaneously. Gen 2's FAQ explicitly permits simultaneous grid and solar charging, with solar prioritized. Do not add the separate maximum input ratings together and assume that sum is a supported charging rate.
Equal-load runtime estimates
Use estimated hours = capacity (Wh) × 0.85 ÷ average AC load (W), following Anker's generic planning formula. The factor is an allowance for losses, not measured efficiency for either generation. These hypothetical loads are sizing examples, not appliance specifications; results below are rounded to whole hours.
| Assumed total AC load | Original: 1,056Wh, estimated hours | Gen 2: 1,024Wh, estimated hours | Original + battery: 2,112Wh, estimated hours |
|---|---|---|---|
| 50W: networking and lights example | About 18 | About 17 | About 36 |
| 100W: average fridge-load example | About 9 | About 9 | About 18 |
| 300W: combined equipment example | About 3 | About 3 | About 6 |
For the middle row, calculate 1,056 × 0.85 ÷ 100, 1,024 × 0.85 ÷ 100, or 2,112 × 0.85 ÷ 100. The standalone generations are close on stored energy; expansion is the substantial runtime change. Fridges cycle, so use your own average consumption and check compressor starting demand separately. See our refrigerator watts guide for load planning.
Winter storage and bundle checks
Anker publishes 32°F–104°F charging and −4°F–104°F discharging ranges for both stations and the expansion battery. A discharge rating below freezing does not authorize charging below freezing. Follow the temperature limits and any on-screen alerts.
For the original and BP1000-family battery, Anker's manuals advise cool, dry storage and weekly capacity checks: recharge fully below 30%, and charge to 100% every three months. Turn the original off and turn off the battery's outputs as their respective instructions specify. Follow the manual supplied with your exact Gen 2 revision for its storage schedule.
Confirm the station
Match generation, capacity, model label and outlet region.
Read the included equipment
Identify the exact panel, battery, charger, bag and cables.
Check the battery path
The original supports expansion; Gen 2 remains standalone.
Check the item condition
Read the selected new or refurbished option and its warranty terms.
Gen 2's US selector offers station-only, panel, alternator-charger, bag and multiple-station options. A pack of stations gives you separate units; it does not change the no-expansion specification. The base “What's in the Box” list names the station, AC charging cable and safety/warranty card; another section also lists a user manual. Confirm solar cables and vehicle-charging equipment in the selected bundle rather than assuming they come with the base station. For a panel kit, record its exact model and wattage before comparing offers.
How we choose
We compare official US specifications, the shared original-family and expansion-battery manuals, and Anker's charging FAQs. The recommendations prioritize expansion compatibility, continuous output, charging conditions and carrying weight. Source conflicts are identified above; runtime figures are calculations using stated assumptions. This is specification research without physical testing.
thisWATT is reader-supported: when you buy through our links, we may earn a commission at no extra cost to you. As an Amazon Associate, thisWATT earns from qualifying purchases. See our disclosure.
Verdict
Buy C1000 Gen 2 for a lighter standalone station and frequent wall refills. Choose the original C1000 when expansion is central to your plan, or add a BP1000 or BP1000X after confirming the exact station and battery labels with Anker. Settle generation, region and included equipment before comparing offers.
Frequently asked questions
Does the BP1000 work with the Anker SOLIX C1000 Gen 2?
No. Anker says the C1000 Gen 2 has no expansion feature. Its current BP1000X page specifies compatibility with the original C1000, and Anker publishes a shared BP1000/BP1000X manual. Choose the original C1000 if an extra battery is essential, and confirm the exact station and battery labels with Anker before ordering; a solar-panel bundle or a pack of separate Gen 2 stations does not change the Gen 2 expansion limitation.
Is the original Anker C1000 better than Gen 2?
The original is our pick for expansion: its 1,056Wh battery can grow to 2,112Wh with a matching battery. Gen 2 is our standalone pick, with 1,024Wh, 2,000W continuous output and a published 49-minute UltraFast recharge. Anker lists 28.44 lb for the original and 24.9 lb for Gen 2. Choose by storage needs and carrying weight rather than the newer name alone.
Why does the C1000 Gen 2 take longer than 49 minutes to charge?
The headline time requires UltraFast Charging, enabled in the Anker app. Anker lists 1,200W normal charging and 1,600W UltraFast charging. Its FAQ says UltraFast activates above a battery-cell temperature of 68°F and charging slows significantly from 32°F to 68°F. A cold station therefore should not be expected to match the headline time, even when the setting is enabled.
How long will a C1000 run a refrigerator?
Use the refrigerator's average draw, including its cycling, rather than assuming every fridge uses the same power. With a hypothetical 100W average AC load and Anker's generic 0.85 efficiency allowance, either standalone generation estimates to about nine hours, rounded to whole hours. An original with its matching battery estimates to about eighteen hours. These are planning calculations; temperature, conversion losses, settings and compressor starts affect the result.
Related guides
LiFePO4 vs Lithium-Ion Power Stations: Cycles and Winter Use
Compare LiFePO4 and other lithium-ion power stations by rated cycles, capacity retention, weight and winter charging limits, with exact-model picks and checks.
Updated November 2, 2026Read
Jackery Explorer 1000 vs 1000 v2 vs 1000 Plus: Which to Buy?
Compare the original Jackery Explorer 1000, 1000 v2 and 1000 Plus: battery types, output, discontinued expansion packs, solar bundles and warranty conditions.
Updated November 2, 2026Read
EcoFlow RIVER 3 vs RIVER 3 Plus: Which Small Station Fits?
Choose the right EcoFlow RIVER 3 for light outages, travel or a gift. Compare Plus, Max bundles, charging, included cables and realistic small-load runtimes.
Updated November 2, 2026Read